Product Search
Search results for 'D-6927'
Showing 21 - 41 of 563 Total Results
(8) options
Location: Manual Compression Testing Machines
Testing range of 2,500 to 250,000 lbs. (11 – 1,112 kN) with an accuracy of ±.5% of indicated load., Supplied with platen set for testing 6" x 12" (150 x 300 mm) cylinders using unbonded or sulfur capping method and steel safety guard doors., Continuous duty hydraulic pump runs quieter, cooler and...
CA-2080
Location: Sieve Storage Rack
This adjustable bench rack holds all diameters of sieves up to 12" (305mm) maximum. Stainless steel rack has non-skid rubber feet, and two permanent and two adjustable rubber-coated sieve support rods.
(4) options
Location: Test Platens
Test both cubes and cylinders . Used for testing 2” (50 mm) cubes and 3” (76 mm) diameter cylinders and cores in compression. Cube test set consists of a spherically seated platen assembly and a lower pedestal used for positioning the cube sample at the correct height for testing. The bearing block...
SA-4010
Location: Dynamic Cone Penetrometer
The Dual Mass DCP Standard Kit from Test Mark measures the shear strength of soil with a CBR between 0.5 - 100%.
(2) options
Location: Test Platens
One fixture tests both 4” and 6” beams. . Used to determine the modulus of rupture for both Center and Third Point beams with depths of either 4” or 6”. The upper heads load bearing blocks are easily changed for center or third point test configuration for either size beam. Bottom support blocks...
SA-2032
Location: CBR Accessories
Machined from seamless tubing with a sharpened edge to enable undisturbed samples to be taken in the field, cutting edge is plated for rust resistance. Recess in upper section allows edge to be mounted at either end of the mold to facilitate sample removal in the field.
Constant Head Permeameter Cell
(5) options
Location: Constant Head Permeameter Cell
The Constant Head Permeameter Cell from Test Mark is used to determine the coefficient of permeability by the constant head method for laminar flow of water through granular soils.
Marshall Automatic Triple Compactor, 4" Rotating Mold
AA-0024
Location: Marshall Automatic Compactor
Automatically compacts three samples at a preset number of hammer blows and shuts off automatically on completion. Unit includes compactor, automatic counter, oak pedestal and 4" mold.
CA-0370
Location: Slump Testing
This cast-aluminum base provides a sturdy, level surface on which to perform slump tests. Cleats dig into the ground for firm, level support.
Capping Compound *TEMPORARILY OUT OF STOCK*
CA-0100
Location: Capping Compound
Test Mark's Ultra-Strength Capping Compound is used to cap the ends of concrete test cylinders so compression force will be evenly distributed to the cylinder during testing.
AA-0040-A
Location: Marshall Hand Compaction Set
Set includes Hand Compaction Hammer, 4" Compaction Mold, Compaction Pedestal with Top Plate, Hammer Support Rod with Adjustable Guide and Compaction Mold Holder.
TM-720
Location: Digital Load Indicating Systems
Simultaneously displays both live load and rate of load, Designed for the harshest laboratory environments with a moisture/dust proof case, Accuracy of ± .5% of indicated load, Made in the USA . Display depicted after test is complete Spreadsheet The i720 is an easy to use digital load indicator...
SA-0650
Location: Mortar & Pestle
Soil mortar, when used with the pestle, is for pulverizing dry samples of soil and other materials. Mortar is made from heavy porcelain with glazed exterior. Rubber-tipped pestle is 8" long and is for grinding soils without breaking individual particles.
CA-2700
Location: Specific Gravity Flasks
The Chapman flask from Test Mark has two bulbs for determining approximate percentage of voids and surface moisture in fine aggregates.
SA-0652
Location: Mortar & Pestle
Rubber-tipped pestle is 8" long and is for grinding soils without breaking individual particles.
Circulating Water Bath, Digital
AA-0065
Location: Circulating Water Bath
The circulating water bath from Test Mark is fully insulated with magnetic circulator for heating up to 12 4-inch diameter Marshall samples at a time.
Magnet Holder with Swivel Adapter Yoke
SA-2021
Location: CBR Accessories
Convenient, portable method of mounting dial indicators. Holder's Alnico magnetic base mounts on flat or curved metallic surfaces. Indicator can me mounted in almost any position.
(2) options
Location: Vebe Consistometer
The Vebe Consistometer determines the consistency and density of low slump roller-compacted concrete - from Test Mark Industries.